Search found 194 matches
- Thu Jul 19, 2012 1:04 am
- Forum: General FOSS EMS
- Topic: Chrysler 42RE Transmission Controller Brainstorming
- Replies: 23
- Views: 80139
Re: Chrysler 42RE Transmission Controller Brainstorming
Basic Coding Milestones (Somewhat in order of precedence) #1 Boot/Debug Dump predefined variables via serial <- basic testing interface Reboot microprocessor on demand (trivial) Respond via VGA/NTSC terminal to serial commands <- reduces need for a laptop later Generate constant data stream when pr...
- Tue Jul 17, 2012 10:28 pm
- Forum: General FOSS EMS
- Topic: Chrysler 42RE Transmission Controller Brainstorming
- Replies: 23
- Views: 80139
Re: Chrysler 42RE Transmission Controller Brainstorming
The best part is it has standard C libraries, so it acts more like Linux than just a plain old microprocessor.Fred wrote:Propeller just got WAY more attractive! CoolPeter wrote:Just out of curiosity have you used the PropellerGCC yet?
http://propgcc.googlecode.com/hg/doc/Library.html
- Tue Jul 17, 2012 10:20 pm
- Forum: General FOSS EMS
- Topic: Chrysler 42RE Transmission Controller Brainstorming
- Replies: 23
- Views: 80139
Re: Chrysler 42RE Transmission Controller Brainstorming
I like though hole stuff better also. I do use quite a few breakout boards for things that don't come in diy type packages. As far as the fets go it's pretty much 6 of one half a dozen of the other. I'm also not a fan of the LM1815. http://forum.diyefi.org/viewtopic.php?f=5&t=1531 Just out of c...
- Tue Jul 17, 2012 10:10 pm
- Forum: General FOSS EMS
- Topic: Chrysler 42RE Transmission Controller Brainstorming
- Replies: 23
- Views: 80139
Re: Chrysler 42RE Transmission Controller Brainstorming
Firmware tasks The following tasks have to be performed by the processor. The load can be spread out across 8 x 20 MIPS cores and 16 hardware timers. Monitor ignition power Track statistics and save in EEPROM (more on this later) Monitor 2 pulse input channels for engine speed and output shaft spee...
- Tue Jul 17, 2012 9:42 pm
- Forum: General FOSS EMS
- Topic: Chrysler 42RE Transmission Controller Brainstorming
- Replies: 23
- Views: 80139
Re: Chrysler 42RE Transmission Controller Brainstorming
Starting to do some visualisations. Note that it is 35 C here today. I spent all day pulling wire and bending conduit in a mechanical room. Yuck.
- Tue Jul 17, 2012 9:13 pm
- Forum: General FOSS EMS
- Topic: Chrysler 42RE Transmission Controller Brainstorming
- Replies: 23
- Views: 80139
Re: Chrysler 42RE Transmission Controller Brainstorming
I'd probably run the solenoids off a VND14NV04, because I have some sitting around not doing anything. You might need an op amp or something similar to shift the voltage to something higher than 3.3V. I never tried to use a PWM on the Propeller. You might consider something like a MCZ33800. It supp...
- Tue Jul 17, 2012 12:10 pm
- Forum: General FOSS EMS
- Topic: Chrysler 42RE Transmission Controller Brainstorming
- Replies: 23
- Views: 80139
Re: Chrysler 42RE Transmission Controller Brainstorming
Yep, Propeller again. When you don't have to worry about microsecond timing it can all be done in the interpreted language instead of assembly. Makes it pretty easy.
My downfall is I rarely get the hardware sorted enough to do some serious coding.
My downfall is I rarely get the hardware sorted enough to do some serious coding.
- Tue Jul 17, 2012 5:47 am
- Forum: General FOSS EMS
- Topic: Chrysler 42RE Transmission Controller Brainstorming
- Replies: 23
- Views: 80139
Re: Chrysler 42RE Transmission Controller Brainstorming
3-4 Shift Solenoid Controlled by on/off current drain. 25-40 Ohms resistance. Engages at closed throttle at 25-28 mph. Disengages at closed throttle below 25 mph. Disabled when OD switch is off. Disabled at wide open throttle. Disabled when temp < 0.5 C (30 F) Disabled when temp > 126 C (260 F) Ena...
- Tue Jul 17, 2012 5:14 am
- Forum: General FOSS EMS
- Topic: Chrysler 42RE Transmission Controller Brainstorming
- Replies: 23
- Views: 80139
Re: Chrysler 42RE Transmission Controller Brainstorming
Transmission Specifications Gear Ratio ---------------- 1 2.74 2 1.54 3 1.00 4 (OD) 0.69 R 2.21 Fluid: ATF+3 Governor Pressure, Solenoid PWM, Pressure Sensor Feedback Speed (MPH) Governor (PSI) Sensor (V) Solenoid (V) Solenoid (PWM%) -----------------------------------------------------------------...
- Tue Jul 17, 2012 5:06 am
- Forum: General FOSS EMS
- Topic: Chrysler 42RE Transmission Controller Brainstorming
- Replies: 23
- Views: 80139
Re: Chrysler 42RE Transmission Controller Brainstorming
Stock I/O Configuration On/Off Solenoids (25-40 Ohms) 3-4 Upshift Torque Convertor Lockup Transmission Relay PWM Solenoid (3-5 Ohms) Governor Pressure (operates at 512 Hz) Analog Sensors Transmission Temperature (1000 Ohms @ 70 F) Governor Pressure (0-5 Volts 0-125 PSIA) Pulse Input Output Shaft Sp...