So, if you are on the list:
viewtopic.php?f=27&t=2273
Code: Select all
First batch:
1. DeuceEFI 1 of 2 - built for vehicle
2. DeuceEFI 2 of 2 - blank for reference/spare
3. Fred 1 - blank, for review/reference
4. Dan 1 - blank, for review and possible use
5. mikehudsonuk 1 - SMD only says urgent, smart guy :-p
These MUST have boards by early November. They can come out of first batch if necessary, or second if time. If second, then 5 from the following list can have 5 from the first batch. I hope these come from a second batch, but the first batch should be held until that can be confirmed.
1. Eric 1 - blank + parts PAID urgent, absolute priority
2. Josh 1 - SMD only, urgent, priority
3. ohollmen 1 - SMD only, urgent, priority
4. E4ODnut 1 of 2 - blank + bdm + bom - has desire to hack and multiple ms1 engines
5. pishta 1 - blank some priority
Prices have changed due to some design changes and the kits will now INCLUDE all the ignitor drivers, the low side drivers, the AAP and MAP sensors this time around.
The capabilities of this board for FreeEMS can be found in the README.md file in my Jaguar repository master branch on github:
https://github.com/DeuceEFI/Jaguar/blob ... /README.md
The full schematics and board layout are in my repository as well.
I generally ship USPS Flat Rate Priority Mail with Delivery Confirmation to USA addresses ($6.00 without the aluminum case or $8.00 with the aluminum case [the aluminum case requires a bigger shipping box]). For international orders, I ship via the United States Postal Service and I can provide you with low cost (slow) or more expensive (faster) shipping options.
I can provide the aluminum alloy cases with flanged ends for an additional $28.00 USD (plus shipping if ordered separately) or you can order them from:
The San Jose Scientific Shop
You will need to cut out the connector holes in the flanged ends of the case.
If you are thinking about Option #1 or Option #2, you should also consider purchasing one of my USBDMs for $32.00 USD which I can include with your Jaguar 0.6-alpha board to save on shipping costs.
Case and connector are NOT included with any of these kits.
So here are your ordering options:
Option #1: Bare Jaguar 0.6-alpha board (REQUIRES BDM!) $15.00 USD
No frills, no components, just the printed circuit board. This option is $15.00 USD plus shipping from USA Zip Code 47433 (ask for a shipping quote if not in the USA).
Option #2: Bare Jaguar 0.6-alpha board with full BOM (REQUIRES BDM!) $250.00 USD
The includes a bare PCB with every component in the Bill Of Materials (BOM) in marked bags so you will know the component value and schematic reference ID. This option is $250.00 USD plus shipping from USA Zip Code 47433 (ask for a shipping quote if not in the USA).
Option #3: Jaguar 0.6-alpha with ALL SMD components installed $140.00 USD
All of the SMD components are installed and the Serial Monitor is installed so you will have USB communications. NO through hole parts are included with this option. I can provide you with a shortened BOM so you can order the remainder of the components from your favorite component vendor. This option is $140.00 USD plus shipping from USA Zip Code 47433 (ask for a shipping quote if not in the USA).
Option #4: Jaguar 0.6-alpha with ALL SMD components installed and BOM kit of parts $280.00 USD
This is a Jaguar 0.6-alpha board that will have all the SMD components installed and will include a full BOM kit of parts (in marked bags so you will know the component value and schematic reference ID) for you to solder on the board. Case and connector are NOT included. This option is $280.00 USD plus shipping from USA Zip Code 47433 (ask for a shipping quote if not in the USA).
Option #5: Jaguar 0.6-alpha fully assembled $380.00 USD
This option gives you a fully assembled Jaguar 0.6-alpha board, with a few parts that you will need to install. You will need to install the voltage regulators and the MAP or AAP sensors. These are included, but you will need to solder them on (don't worry they have large leads and big pads to solder). This option is $380.00 USD plus shipping from USA Zip Code 47433 (ask for a shipping quote if not in the USA).
Options #2, #3, #4 and #5 have the following choices:
- TC4427A non-inverting output ignitor drivers OR TC4426A inverting output ignitor drivers
115kPa, 250kPa or 400kPa MAP sensor
For those of you who order Option #1 or Option #2 and you do not already have a Background Debug Module (BDM), I have those for sale as well, they are $32.00 USD (plus shipping if ordered separately), but the BDM is small enough that it can be included in the same shipping carton as Option #1 or Option #2, so there will be no additional shipping charge if purchased with those options. If you would like to purchase a BDM with Option #3, #4 or #5, I can also ship it in the same shipping carton as those kits without any additional shipping cost. My BDM is based on USBDM and additional information can be found at: http://www.coolefi.com/usbdm.php
EDIT: I cleaned up the paragraphs as they were hard to follow.
Note: When using PayPal to send funds, please use the "Send to friend" option and cover the PayPal fees as the prices above do not include the PayPal fee for the transaction.